manualshive.com logo in svg

Siemens FCT010/DSL, Operating Instructions Manual, Page: 28 / 180

Share
Download
Siemens FCT010/DSL Operating Instructions Manual Download Page 28

WARNING

Exceeded maximum permissible operating pressure

Risk of injury or poisoning.

The maximum permissible operating pressure depends on the device version, pressure limit 
and temperature rating. The device can be damaged if the operating pressure is exceeded. Hot, 
toxic and corrosive process media could be released.

Ensure that maximum permissible operating pressure of the device is not exceeded. Refer to 
the information on the nameplate and/or in Technical data (Page 107).

WARNING

Incorrect mounting at Zone 0

Risk of explosion in hazardous areas.
• Ensure sufficient tightness at the process connection.
• Observe the standard IEC/EN 60079-14.

WARNING

Loss of explosion protection

Risk of explosion in hazardous areas if the device is open or not properly closed.
• Close the device as described in Installing/mounting (Page 27).

CAUTION

External stresses and loads

Damage to device by severe external stresses and loads (e.g. thermal expansion or pipe 
tension). Process media can be released.
• Prevent severe external stresses and loads from acting on the device.

4.1.1

Installation location requirements

NOTICE
Strong vibrations

Damage to device.
• In installations with strong vibrations, mount the transmitter in a low vibration 

environment.

Installing/mounting
4.1 Basic safety notes

SITRANS MASS 2100 & FC300 (FCT010/DSL)

28

Operating Instructions, 06/2020, A5E39788682-AB

Summary of Contents for FCT010/DSL





















































































































































































Reviews:

No comments