Siemens FC300 Operating Instructions Manual Download Page 78 | Manualshive

Page: 78 / 518

Siemens FC300 Operating Instructions Manual Download Page 78

6. Mount power supply protection cover and fasten protection cover screw.
7. Tighten cable gland.

5.2.4.8

Step 4b: Connecting the inputs and outputs (channels 2 to 4)

1. Remove cap and ferrule from cable gland and slide onto cable.
2. Push cable through open gland and cable path.
3. Restore ferrule and tighten cap to lightly hold cable in place.
4. Fold signal cable screen back over outer sheath and ground beneath cable clamp.
5. Connect wires to terminals using wiring tool.

11

12

12

13

Active current output

Passive current output

⑫

IO[3] (common)

⑬

IO[3]- (passive)

⑪

IO[3]+ (active)

⑫

IO[3] (common)

Functional Earth

Functional Earth

Termination example for channel 3

6. Tighten cable gland.

Note
Active or passive current output is preselected at ordering.

Connecting
5.2 Connecting MASS 2100/FC300

MASS 2100 & FC300 (FCT030)

78

Operating Instructions, 06/2017, A5E39789040-AA

«
...
76
77
78
79
80
...
»

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments