manualshive.com logo in svg

Siemens FC300, Operating Instructions Manual, Page: 70 / 518

Share
Download
Siemens FC300 Operating Instructions Manual Download Page 70

The following table shows:
● Which cable with which terminal
● Hardware and software configuration of the channels

3RZHU6XSSO\

&KDQQHO

&KDQQHO

&KDQQHO

&KDQQHO

7HUPLQDOV

/

1

$FWLYH

1&

12

1&

12

3RZHU6XSSO\

&KDQQHO0RGEXV

&KDQQHO3URILEXV

&KDQQHO2XWSXW

2XWSXWV&XUUHQW)UHTXHQF\3XOVHDQGVWDWXV

,QSXWV'LJLWDO

&XUUHQ$57

&XUUHQW)UHTXHQF\

3XOVHDQG6WDWXV

&$57

6:FRQILJXUDWLRQ

+:FRQILJXUDWLRQ

&KDQQHOVDQG

,QSXWRXWSXW

&KDQQHOVDQG

5HOD\

6WDWXVRXWSXW

&RPPRQ

&RPPRQ 3DVVLYH

,Q$

,Q%

2XW$

2XW%

,Q$

,Q%

2XW$

2XW%

$FWLYH &RPPRQ

&RPPRQ 3DVVLYH

$FWLYH &RPPRQ

&RPPRQ 3DVVLYH

$FWLYH &RPPRQ

&RPPRQ 3DVVLYH

Figure 5-3

Termination/configuration overview

5.2.4.3

Connecting the Current HART, CH1

Note
4 to 20 mA output
It is not required to use shielded cables for the pure 4 to 20 mA current output.

Note
HART communication
It is recommended by the FieldComm Group (FCG) to use shielded cables for the HART 

communication.

Note
Passive channels only
Channel 1 power supply must be separated from that for channels 2 to 4.
Signal return (or common) can be joined.

1. Remove cap and ferrule from cable gland and slide onto cable.
2. Push cable through open gland and cable path.
3. Restore ferrule and tighten cap to lightly hold cable in place.
4. Signal cable screen is folded back over outer sheath and grounded beneath cable clamp.

Connecting
5.2 Connecting MASS 2100/FC300

MASS 2100 & FC300 (FCT030)

70

Operating Instructions, 06/2017, A5E39789040-AA

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments