Siemens FC300 Operating Instructions Manual Download Page 39 | Manualshive

Page: 39 / 518

Siemens FC300 Operating Instructions Manual Download Page 39

4.1.1

Installation location requirements

NOTICE
Strong vibrations
Damage to device.
● In plants with strong vibrations, mount the transmitter in a low vibration environment.

CAUTION

Aggressive atmospheres
Damage to device through penetration of aggressive vapors.
● Ensure that the device is suitable for the application.

CAUTION

Direct sunlight
Device damage.
The device can overheat or materials become brittle due to UV exposure.
● Protect the device from direct sunlight.
● Make sure that the maximum permissible ambient temperature is not exceeded. Refer to

the information in Technical data (Page 215).

WARNING

Insufficient air supply
The device may overheat if there is an insufficient supply of air.
● Install the device so that there is sufficient air supply in the room.
● Observe the maximum permissible ambient temperature. Refer to the information in the

section Technical data (Page 215).

Installing/mounting

4.1 Basic safety notes

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

39

«
...
37
38
39
40
41
...
»

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments