Siemens FC300 Operating Instructions Manual Download Page 34 | Manualshive

Page: 34 / 518

Siemens FC300 Operating Instructions Manual Download Page 34

3.5

Applications

Measurement of liquids and gases

SITRANS F C Coriolis mass flowmeters are designed for measurement of a variety of liquids

and gases. The flowmeters are multi-parameter devices offering accurate measurement of

massflow, volumeflow, density, temperature and, depending on product variants, fraction,

including industry-specific fractions.

Main applications

The main applications of the Coriolis flowmeter can be found in all industries, such as:
● Chemical & Pharma: detergents, bulk chemicals, acids, alkalis, pharmaceuticals, blood

products, vaccines, insulin production

● Food & Beverage: dairy products, beer, wine, soft drinks, °Brix/°Plato, fruit juices and pulps,

bottling, CO

2

dosing, CIP/SIP-liquids, mixture recipe control

● Automotive: fuel injection nozzle & pump testing, filling of AC units, engine consumption,

paint robots

● Oil & Gas: filling of gas bottles, furnace control, test separators, bore-hole plasticizer dosing,

water-cut metering

● Water & Waste Water: dosing of chemicals for water treatment

3.6

Approvals

Note
For further details see Approvals (Page 239).

The device is available with approvals for general purpose and for hazardous areas. In all

cases, check the nameplate on your device, and confirm the approval rating.

3.7

Theory of operation

The Coriolis principle of measurement

The flow measurement is based on the Coriolis law of motion. Particles moving in a rotating /

oscillating system will resist imposed oscillations in a manner consistent with their mass and

velocity (momentum). Oscillation produced by a Coriolis flowmeter where the process media

is accelerated around bends results in phase distortions of the measuring tubes.
The SITRANS F C sensors are energized by an electromagnetic (voice coil) driver circuit which

oscillates the pipes at their resonant frequency. Two pickups are placed symmetrically on either

side of the driver to provide position signals for digital processing.

Description
3.7 Theory of operation

MASS 2100 & FC300 (FCT030)

34

Operating Instructions, 06/2017, A5E39789040-AA

«
...
32
33
34
35
36
...
»

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments