manualshive.com logo in svg

Siemens FC300, Operating Instructions Manual, Page: 240 / 518

Share
Download
Siemens FC300 Operating Instructions Manual Download Page 240

Description

Specification

MASS 2100

 

ATEX

Certificate : DEMKO 03 ATEX 135252X
Sitrans FC MASS 2100 can be used in zone 0, 20
Ex ia IIC T6…T3 Ga
Ex ia IIIC T135°C…T180°C Da

IECEx 

Certificate : IECEx ULD 17.0029
Sitrans FC MASS 2100 can be used in zone 0, 20
Ex ia IIC T6…T3 Ga
Ex ia IIIC T135°C…T180°C Da

Canada 

Certificate. UL E232147
Sitrans FC MASS 2100 can be used in zone 0, 20 

and Class I+II+III Division 1. Grp. A,B,C,D, E, F, G
Class I+II+III Division 1. Grp. A,B,C,D, E, F, G.
Ex ia IIC T6…T3 Ga
Ex ia IIIC T135°C…T180°C Da

US

Certifikate: UL E232147
Sitrans FC MASS 2100 can be used in zone 0 and 

Class I Division 1.
Class I+II+III Division 1. Grp. A,B,C,D, E, F, G.
AEx ia IIC T6…T3 Ga
AEx ia IIIC T135°C…T180°C Da

Pressure equipment

2014/68/EU Pressure Equipment Directive (PED)
Canadian Registration Number (CRN)

11.11

SensorFlash

Table 11-29 SensorFlash     

Description

Specification
SD card

Capacity

4 GB

File system support

FAT32 / 8.3

Temperature range

Operation:

Storage:

-40 to +85 °C (-40 to 185 °F)

-40 to +100 °C (-40 to 212 °F)

Note
SensorFlash functions support
Only the supplied 4 GB SD cards are supported for backup, restore, logging, and firmware 

update.

Technical data
11.11 SensorFlash

MASS 2100 & FC300 (FCT030)

240

Operating Instructions, 06/2017, A5E39789040-AA

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments