manualshive.com logo in svg

Siemens FC300, Operating Instructions Manual, Page: 188 / 518

Share
Download
Siemens FC300 Operating Instructions Manual Download Page 188

SIMATIC PDM / PLC

NAMUR NE 107

Description
 

Measure
 

Icon

Device 

status

Pri‐

ority

Icon

Device 

status

Pri‐

ority

Process 

value 

alarm

8

Out of 

specifica‐

tion

4

Deviations from permissible ambient 

or process conditions determined by 

device (through self-monitoring, or 

faults in device) indicate that meas‐

urement is uncertain, or deviations 

from set value in actuators is proba‐

bly greater than expected under nor‐

mal operating conditions.
Process or ambient conditions will 

damage device or result in uncertain 

output.

Check ambient tempera‐

ture or process conditions. 

If possible, relocate de‐

vice.

Process 

value 

warning

9

Out of 

specifica‐

tion

4

Deviations from permissible ambient 

or process conditions determined by 

device (through self-monitoring, or 

warnings in device) indicate that 

measurement is uncertain, or devia‐

tions from set value in actuators is 

probably greater than expected un‐

der normal operating conditions.
Process or ambient conditions could 

damage device or result in uncertain 

output.

Check ambient tempera‐

ture or process conditions. 

If possible, relocate de‐

vice.

10.2

Fault codes and corrective actions

Alarms and system messages support both Siemens standard alarm classes and NAMUR 

status signals.
In the following tables the alarm IDs (identification numbers) are listed along with possible 

causes and directions for corrective action.

Diagnosing and troubleshooting
10.2 Fault codes and corrective actions

MASS 2100 & FC300 (FCT030)

188

Operating Instructions, 06/2017, A5E39789040-AA

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments