Siemens FC300 Operating Instructions Manual Download Page 18

Page: 18 / 518

Further provisions for hazardous area applications are for example:
● IEC 60079-14 (international)
● EN 60079-14 (EC)

2.2.1

FCC Conformity

US Installations only: Federal Communications Commission (FCC) rules

WARNING

Improper device modifications
Danger to personnel, system and environment can result from improper modifications to the

device.
● Changes or modifications not expressly approved by Siemens could void the user’s

authority to operate the equipment.

Note
● This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment.

● This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the operating instructions, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference to radio communications, in which case the user will be required to

correct the interference at his own expense.

2.2.2

Conformity with European directives

The CE marking on the device symbolizes the conformity with the following European

directives:

Electromagnetic

compatibility EMC

2014/30/EU

Directive of the European Parliament and of the Council on the harmoni‐

sation of the laws of the Member States relating to electromagnetic com‐

patibility

Low voltage direc‐

tive LVD

2014/35/EU

Directive of the European Parliament and of the Council on the harmoni‐

sation of the laws of the Member States relating to the making available

on the market of electrical equipment designed for use within certain volt‐

age limits

Safety notes
2.2 Laws and directives

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Search results

Summary of Contents for FC300

Reviews:

Siemens FC300, Operating Instructions Manual, Page: 18 / 518

Search results

Summary of Contents for FC300

Reviews: