manualshive.com logo in svg

Siemens FC300, Operating Instructions Manual, Page: 167 / 518

Share
Download
Siemens FC300 Operating Instructions Manual Download Page 167

Service and maintenance

9

9.1

Basic safety notes

Note
The device is maintenance-free.

The device is maintenance-free. However, a periodic inspection according to pertinent 

directives and regulations must be carried out.   
An inspection can include check of:
● Ambient conditions
● Seal integrity of the process connections, cable entries, and cover screws
● Reliability of power supply, lightning protection, and grounds

WARNING

Impermissible repair of explosion protected devices
Risk of explosion in hazardous areas
● Repair must be carried out by Siemens authorized personnel only.

WARNING

Dust layers above 5 mm
Risk of explosion in hazardous areas.
Device may overheat due to dust build up.
● Remove dust layers in excess of 5 mm.

NOTICE
Penetration of moisture into the device
Device damage.
● Make sure when carrying out cleaning and maintenance work that no moisture penetrates 

the inside of the device.

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

167

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments