Siemens FC300 Operating Instructions Manual Download Page 111 | Manualshive

Page: 111 / 518

Siemens FC300 Operating Instructions Manual Download Page 111

Operating MASS 2100/FC300 with FCT030

7

7.1

Chapter overview Operating

A considerable amount of information regarding the operation and status of the flowmeter is

available to the user via the local display (HMI ) and SIMATIC PDM.
In this chapter you will find information on how to monitor and operate the device using the

local display (HMI).

7.2

Operating instructions

7.2.1

Local display (HMI)

Operation via local user interface

The device is operated with the capacitive proximity keypad on the local user interface.
The elements are actuated by touching the glass panel above the appropriate key. The glass

is 10 mm (3/8") thick. Pressing harder will not activate the key, but using a thumb instead of a

finger tip will help. The text display above the operating elements gives a menu-guided

operation of the individual device function/parameters. Successful operation of the key is

confirmed by a small green LED at the right of the display.

①

Full graphical display

②

LED (for indication of key operation)

③

Capitance proximity keypad

Figure 7-1

Local user interface

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

111

«
...
109
110
111
112
113
...
»

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments