manualshive.com logo in svg

Siemens FC300, Operating Instructions Manual, Page: 11 / 518

Share
Download
Siemens FC300 Operating Instructions Manual Download Page 11

Introduction

1

Note
This manual applies to the Coriolis flowmeter SITRANS FC MASS 2100 / FC300 with 

transmitter FCT030, from firmware xx

This document are standard delivered in electronic media with the device. Latest version can 

be downloaded at www.siemens.com (

http://support.automation.siemens.com/WW/view/en/

60666565/134200

)

These instructions contain all information required to commission and use the device. Read 

the instructions carefully prior to installation and commissioning. In order to use the device 

correctly, first review its principle of operation.
The instructions are aimed at persons mechanically installing the device, connecting it 

electronically, configuring the parameters and commissioning it, as well as service and 

maintenance engineers.

1.1

Document history

The following table shows major changes in the documentation compared to the previous 

edition.   

Edition

Remarks

EDD version

FW revision

02/2017

● First edition

 

 

Use the device to measure process medium in accordance with the information in the 

Operating Instructions.

Note
Use in a domestic environment
This Class A Group 1 equipment is intended for use in industrial areas. 
In a domestic environment this device may cause radio interference.

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

11

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Reviews:

No comments