Siemens ET 200SP HA Page 35 Equipment Manual Download

Page: 35 / 48

Technical specifications

8.1

Technical specifications

Article number

6DL1155-6AU00-0PM0

General information

Product type designation

IM 155-6 PN

HW functional status

FS03

Firmware version

V1.1

Vendor identification (VendorID)

02AH

Device identifier (DeviceID)

030FH

Product function

• I&M data

Yes; I&M0 to I&M3

Engineering with

• STEP 7 TIA Portal configurable/integrated

from version

V16

• STEP 7 configurable/integrated from version V5.6
• PCS 7 configurable/integrated from version

V9.0

• PCS neo can be configured/integrated from

version

V3.0

Configuration control

via dataset

Supply voltage

Rated value (DC)

24 V

permissible range, lower limit (DC)

19.2 V

permissible range, upper limit (DC)

28.8 V

Reverse polarity protection

Yes

Short-circuit protection

Yes

Mains buffering

• Mains/voltage failure stored energy time

10 ms

Input current

Current consumption, max.

700 mA; +19.2 V to +28.8 V DC

Inrush current, max.

5 A

I²t

0.36 A²·s; Due to increased mains buffering of 10
ms

Power

Infeed power to the backplane bus

7.5 W; no doubling in redundant mode as the in‐
feed power is also designed as redundant

Power loss

Power loss, typ.

2.4 W

Address area

Address space per module

IM 155-6 PN HA
Equipment Manual, 09/2021, A5E39262148-AE

Summary of Contents for ET 200SP HA

















































Search results

Summary of Contents for ET 200SP HA

Reviews:

Related manuals for ET 200SP HA

Brands by name

Popular brands

Siemens ET 200SP HA, Equipment Manual

Search results

Summary of Contents for ET 200SP HA

Reviews:

Related manuals for ET 200SP HA

Brands by name

Popular brands