manualshive.com logo in svg

Siemens Drager medical Carina, Instructions For Use Manual, Page: 48 / 144

Share
Download
Siemens Drager medical Carina Instructions For Use Manual Download Page 48

Preparation

48

Instructions for Use Carina SW 3.n

External battery connection 
1

Insert the DC connector in the Carina.

2

Connect the external battery. Refer to the 
Instructions for Use of the external battery.

The external battery is not charged from the Carina 
mains supply!

External battery for 3rd party connection

12 to 24 V DC (–10 % to +30 %); 6.3 to 3.2 A
Ensure that the battery is connected with correct 
polarity!

1

Insert the plug.

2

Connect a microfuse (6.3 A slow blow) to the 
external battery.

3

Connect the cable to the microfuse.
The LED 

 flashes or lights up according to 

the charge of the internal battery.

The external battery is not charged from the Carina 
mains supply!

WARNING
Mains-powered equipment must not be con-
nected to the connection for an external bat-
tery. Risk of electric shock or equipment 
damage. 

CAUTION

Avoid high resistance in conjunction with the 
external battery by keeping the electrical connec-
tors clean at all times to avoid insufficient power 
being delivered to the device.

CAUTION

The external battery must always have sufficient 
capacity as directed in the Instructions for Use for 
the external battery.

092

External battery

01

1

- +

1

2

3

Summary of Contents for Drager medical Carina

















































































































































Reviews:

No comments