manualshive.com logo in svg

Siemens Drager medical Carina, Instructions For Use Manual, Page: 45 / 144

Share
Download
Siemens Drager medical Carina Instructions For Use Manual Download Page 45

Instructions for Use Carina SW 3.n

45

Preparation

Respiratory gas humidifier with inspiratory 
heater  
For hose system with leak valve

z

Turn the switch to leak valve »

«, see 

page 41.

1

Connect the filter to socket »

«.

2

Fit the ventilation hoses according to the 
instructions for the respiratory gas humidifier, 
observing hose lengths.

3

Install the leak valve, making sure the direction 
is correct.

For hose system with expiratory valve

z

Turn the switch to expiratory valve »

«, 

see page 41.

1

Connect the filter to socket »

«.

2

Fit the ventilation hoses according to the 
instructions for the respiratory gas humidifier, 
observing hose lengths.

3

Connect the expiratory valve to the nozzle of 
the ventilation hose.

4

Connect the pilot line of the expiratory valve to 
pilot hose socket »

«.

040

40 cm

110 cm

2

1

3

041

40 cm

110 cm

1

2

3

4

Summary of Contents for Drager medical Carina

















































































































































Reviews:

No comments