manualshive.com logo in svg

Siemens Drager medical Carina, Instructions For Use Manual, Page: 44 / 144

Share
Download
Siemens Drager medical Carina Instructions For Use Manual Download Page 44

Preparation

44

Instructions for Use Carina SW 3.n

Respiratory gas humidifier without inspiratory 
heater  
For hose system with leak valve

z

Turn the switch to leak valve »

«, see 

page 41.

1

Connect the filter to socket »

«.

2

Connect ventilation hoses, observing hose 
lengths!

3

Place the water trap vertically at the lowest 
point of the hose connection.

4

Connect the leak valve, making sure the direc-
tion is correct.

For hose system with expiratory valve

z

Turn the switch to expiratory valve »

«, 

see page 41.

1

Connect the filter to socket »

«.

2

Connect ventilation hoses, observing hose 
lengths!

3

Place the water trap vertically at the lowest 
point of the hose connection.

4

Connect the expiratory valve to the nozzle of 
the ventilation hose.

5

Connect the pilot line of the expiratory valve to 
pilot hose socket »

«.

03

8

35 cm

60 cm

60 cm

2

3

4

1

039

35 cm

60 cm

60 cm

2

3

4

5

1

Summary of Contents for Drager medical Carina

















































































































































Reviews:

No comments