manualshive.com logo in svg

Siemens Drager medical Carina, Instructions For Use Manual, Page: 18 / 144

Share
Download
Siemens Drager medical Carina Instructions For Use Manual Download Page 18

System Overview

18

Instructions for Use Carina SW 3.n

Control panel, top

1

Carrying handle

2

Screen for application-specific information on 
ventilation

3

Buttons for selecting functions and ventilation 
parameters 

4

Centre rotary knob for setting and confirming 
functions and parameters

5

»

Audio paused 2 min.

« button for suppressing 

the alarm tone for 2 minutes and 
for visual indication of alarm status: 
red = warning, yellow = caution

6

LED for indicating power supply:
LED lit = External power supply (mains/external 
battery), internal battery is charged
LED flashes = External power supply 
(mains/external battery), internal battery is 
being charged
LED off = battery operation

7

»

Start/Standby

« button to switch between 

standby and ventilation

8

»

Select

 

Menu

« button to open the menus for 

ventilation settings, alarms, measured values, 
configuration, interlock

Carina underside

9

Switch for hose system with leak valve or hose 
system with expiratory valve masked by sliding 
cover (not illustrated)

10

Base humidifier (accessory, currently not fitted)

11

Holes for positioning on the trolley (4 off)

CAUTION

Switching between a hose system with leak valve 
and a hose system with expiratory valve must be 
carried out by properly trained personnel only! 
Risk of malfunction!

000

1

4
5

2

3

8

7

6

001

9

10

11

Summary of Contents for Drager medical Carina

















































































































































Reviews:

No comments