manualshive.com logo in svg

Siemens CP 443-5 Extended, Manual

Share
Download
Siemens CP 443-5 Extended Manual Download Page 15

4

Displays and Mode Selector

B4 - 15

CP 443-5 Extended for PROFIBUS / Manual Part B4
Release 6/2005

C79000-G8976-C162-06

4

Displays and Mode Selector

LED Display of the Operating Status of the CP 

INTF (red)
EXTF (red)
BUSF (red)

RUN (green)
STOP (yellow)

Front
panel:

The different combinations of the five LEDs on the front panel indicate the status of
the CP:

Table 4-1

 

INTF LED

EXTF LED

BUSF LED

RUN LED

STOP LED

CP Operating Status

Starting up (STOP->RUN)

Running (RUN)

Stopping (RUN->STOP)

Stopped (STOP)

STOP with internal error or
memory reset.

Waiting for firmware update
(duration 10 seconds after power
on)

Waiting for firmware update (CP
currently has an incomplete
firmware version).

S

Download in RUN active / CiR

S

RUN with internal error (for
example, bad configuration
data)

PROFIBUS bus errors

RUN; however problems on DP
chain (DP slave not in data transfer
or not accessible)

RUN; however problems on DP
chain (faulty module in DP slave).

Module fault / system error

Legend:                              on

off

flashing

Field gray: undefined / any

Summary of Contents for CP 443-5 Extended




























Reviews:

No comments

Brands by name

Popular brands

Load more brands