manualshive.com logo in svg

Siemens CP 1243-8 IRC, Operating Instructions Manual

Share
Download
Siemens CP 1243-8 IRC Operating Instructions Manual Download Page 40

Installation, connecting up, commissioning 

 

3.2 Installing, connecting up and commissioning 

 

CP 1243-8 IRC 

40

 

Operating Instructions, 06/2015, C79000-G8976-C385-01 

Pulling/plugging the module 

 

 

NOTICE 
Turning off the station when plugging/pulling the module 
Before pulling or plugging the module, always turn off the power supply to the station. 

 

Dimensions for installation 

 

Figure 3-1 

Dimensions for installation of the S7-1200 

Table 3- 1 

Dimensions for installation (mm)  

S7-1200 devices 

Width A 

Width B * 

CPU (examples) 

CPU 1211C, CPU 1212C 

90 mm 

45 mm 

CPU 1214C 

110 mm 

55 mm 

Communications inter-

faces (examples) 

CM 1241, CM 1243-5, CM 1242-5 

30 mm 

15 mm 

CP 1242-7, CP 1243-1, CP 1243-7, CP 1243-8 IRC 

30 mm 

15 mm 

 * Width B: The distance between the edge of the housing and the center of the hole in the DIN rail mounting clip 

You will find detailed dimensions of the module in the section Dimension drawings 

(Page 113). 

DIN rail clamps, control panel installation 

All CPUs, SMs, CMs and CPs can be installed on the 35 mm DIN rail in the cabinet. Use the 

pull-out DIN rail mounting clips to secure the device to the rail. These mounting clips also 

lock into place when they are extended to allow the device to be installed in a switching 

panel. The inner dimension of the hole for the DIN rail mounting clips is 4.3 mm. 

Summary of Contents for CP 1243-8 IRC













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands