manualshive.com logo in svg

Siemens CP 1243-8 IRC, Operating Instructions Manual

Share
Download
Siemens CP 1243-8 IRC Operating Instructions Manual Download Page 3

 

CP 1243-8 IRC 
Operating Instructions, 06/2015, C79000-G8976-C385-01 

3

 

Preface 

 

 

Preface 

Validity of this manual 

This document contains information on the following product: 

●

 

CP 1243-8 IRC 

Article number 6GK7 243-8RX30-0XE0 

Hardware product version 1 

Firmware version V2.1 
The CP is the communications processor for connection of the SIMATIC S7-1200 via 

public or private infrastructures to a telecontrol master station. The communication is 

handled using the SINAUT ST7 protocol. 
With the help of VPN technology and the firewall, the CP allows protected access to the 

S7-1200. 
The CP can also be used as an additional interface of the CPU for S7 communication. 

 

Figure 1 

CP 1243-8 IRC 

Behind the top hinged cover of the module housing, you will see the hardware product 

version to the right of the article number printed as a placeholder "X". If the printed text is, for 

example, "X 2 3 4", "X" would be the placeholder for hardware product version 1. 
You will find the MAC address under the lower hinged cover of the housing. 

Summary of Contents for CP 1243-8 IRC













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands