Siemens CP 1243-7 LTE Operating Instructions Manual Download Page 6 | Manualshive

Page: 6 / 154

background image

Preface

CP 1243-7 LTE

6

Operating Instructions, 04/2017, C79000-G8976-C381-03

always use the latest product versions. Use of product versions that are no longer supported,

and failure to apply latest updates may increase customer’s exposure to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS

Feed under

Link: (

http://www.siemens.com/industrialsecurity

Firmware

The firmware is signed and encrypted. This ensures that only firmware created by Siemens

can be downloaded to the device.

Recycling and disposal

The product is low in pollutants, can be recycled and meets the requirements of the WEEE

directive 2012/19/EU "Waste Electrical and Electronic Equipment".
Do not dispose of the product at public disposal sites. For environmentally friendly recycling

and the disposal of your old device contact a certified disposal company for electronic scrap

or your Siemens contact.
Keep to the local regulations.
You will find information on returning the product on the Internet pages of Siemens Industry

Online Support:

Link: (

https://support.industry.siemens.com/cs/ww/en/view/109479891

SIMATIC NET glossary

Explanations of many of the specialist terms used in this documentation can be found in the

SIMATIC NET glossary.
You will find the SIMATIC NET glossary here:

●

SIMATIC NET Manual Collection or product DVD
The DVD ships with certain SIMATIC NET products.

●

On the Internet under the following address:
Link: (

https://support.industry.siemens.com/cs/ww/en/view/50305045

Training, Service & Support

You will find information on Training, Service & Support in the multi-language document

"DC_support_99.pdf" on the data medium supplied with the documentation.

«
...
4
5
6
7
8
...
»

Summary of Contents for CP 1243-7 LTE



























































































































































Reviews:

No comments

Related manuals for CP 1243-7 LTE

Brand: ABB Pages: 139

Brand: ABB Pages: 28

Brand: ABB Pages: 59

Brand: Aalborg Pages: 128

Brand: CAME Pages: 12

Brand: CAME Pages: 16

Brand: Ultrak Pages: 41

Brand: Zander Aachen Pages: 10

Brand: Camozzi Pages: 33

Brand: Camozzi Pages: 2

Brand: Camozzi Pages: 64

Brand: Garmin Pages: 4

Brand: jbc Pages: 4

Brand: jbc Pages: 4

Brand: NAPCO Pages: 48

Magnum Alert 2600

Brand: NAPCO Pages: 68

Brand: Vaillant Pages: 11

Brand: IBC Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands