Siemens CERBERUS PYROTRONICS PXL Installation, Operation And Maintenance Manual Download Page 43

Page: 43 / 83

Operation

PXL Conventional Fire Alarm Control Panel

Silenced,

and

Partial Disable

LEDs are off, and the internal

sounder is off. The following screen is displayed on the PXL:

TIME
COMPANY NAME

PXL SYSTEM NORMAL

<MENU

Program

The Program Mode is used for system configuration, test, control,

and history functions.

When the PXL is in Program Mode, it does

not indicate alarm or supervisory conditions.

The System resets to normal mode after 2 minutes of front panel

inactivity. When the PXL is in the Walk Test Mode, it automatically

returns to normal mode after 20 minutes of inactivity.

Responding to a Fire Alarm

HOW THE SYSTEM ANNUNCIATES FIRE ALARMS

When a fire is detected on one of the initiating device circuits (IDCs),

the PXL causes the

System ALARM

LED and the appropriate

Zone

ALARM

LED on the front panel to flash and the systems internal

audible to sound.

NOTE:

Building occupants should follow the fire emergency evacu-

ation plan approved by the building owner. Then alert the

local Fire Department.

TO ACKNOWLEDGE ALARMS

1. Unlock and open the door.
2. System operator should ACKNOWLEDGE the Fire Alarm by

pressing the ACKNOWLEDGE button on the display.

TO SILENCE THE NOTIFICATION APPLIANCE CIRCUITS

System operator should SILENCE the audibles by pressing the

SILENCE button. Subsequent alarm conditions from other zones will

cause the audibles to sound again, DO NOT RESET THE SYSTEM.

A fire official should locate the cause of the alarm.

TO RESET

Press the

RESET

button. (The system will not reset until all alarms,

supervisories, and troubles are acknowledged and all conditions are

returned to normal.)

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of Contents for CERBERUS PYROTRONICS PXL




















































































Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands

Siemens CERBERUS PYROTRONICS PXL, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands