Siemens Cerberus PRO FC721 Technical Manual Download Page 58

Page: 58 / 118

Installation
C-NET detector line

58 | 118
Building Technologies

A6V10211100_f_en_--

Fire Safety

2015-12-15

6.5.1 Connectable C-NET devices

The table below contains a list of all devices which can be connected to the C-NET

detector line. It also highlights which devices feature an alarm indicator (AI) and to

which an external alarm indicator (Ext. AI) or a sounder base (DBS720) can be

connected.

Device type

Type

Description

↑ AI

Ext. AI

DBS 720

Heat detector

HI720

Heat detector for demanding

applications

HI722

Heat detector for standard applications

Flame detector

FDF241-9

Flame detector with three sensors for

demanding applications with many

deceptive phenomena

–

Smoke detector

FDL241-9

Linear smoke detector for demanding

applications with many deceptive

phenomena

–

OP720

Optical smoke detector for standard

applications with few deceptive

phenomena

Multi-sensor

detector

OH720

Simple optical-thermal point detector

OOH740

Optical-thermal multi-sensor fire

detector for demanding application

OOHC740

Optical-thermal multi-sensor fire

detector with CO measurement

OOH740-A9-Ex

Optical-thermal multi-sensor fire

detector with ambient supervision with

collective DualProtocol and FDnet/C-

NET. For areas at risk of explosion

Aspirating smoke

detector

FDA221

Aspirating smoke detector up to a

monitoring area of 500 m

FDA241

Aspirating smoke detector up to a

monitoring area of 800 m

Summary of Contents for Cerberus PRO FC721























































































































Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands

Siemens Cerberus PRO FC721, Technical Manual

Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands