manualshive.com logo in svg

Siemens AXIOM Iconos R200, Operator'S Manual, Page: 68 / 238

Share
Download
Siemens AXIOM Iconos R200 Operator'S Manual Download Page 68

System Operation

System Settings

16 

/ 32

AXD3-340.620.13.01.02

Operator Manual

Lowering the tabletop completely with the table vertical

◆

Move the table into a vertical position (+ 90°).

System remote

control console

◆

Press the down button until the tabletop stops automatically at 120 mm from 
the floor.

◆

Release the button and press it once again
– The tabletop moves maximum to 40 mm from the floor
– an acoustic signal sounds during the tabletop movement

Tableside control

panel

◆

Press the right

1

 button until the tabletop stops automatically at 120 mm from 

the floor.

◆

Release the button and press it once again
– The tabletop moves maximum to 40 mm from the floor
– an acoustic signal sounds during the tabletop movement

Warning

If the tabletop is lowered to less than 12 cm above the floor with the table 
vertical, it is possible for feet to be crushed.

◆

Make sure before remote operation that no one is in the direct vicinity of the 
system.

◆

Avoid a location directly at the table end in the case of tableside operation.

You will hear a warning tone, if the tabletop is lowered to less than 120 mm 
above the floor.

◆

Then control the movement with increased caution.

1

Display in horizontal table position

Summary of Contents for AXIOM Iconos R200















































































































































































































































Reviews:

No comments