Siemens AXIOM Iconos R200 Operator'S Manual Download Page 207

Page: 207 / 238

Accessories

Optional Accessories

AXIOM Iconos R200

AXD3-340.620.13.01.02

/ 54

Armrest

Application

For securing the patient’s arm for injections, IV’s, or insertion of a catheter.

Attachment

◆

Move the patient table to the horizontal position.

◆

Position the patient.

◆

Open the clamping lever (1a).

◆

Place the armrest onto the front or rear accessory rail and slide it into position.

◆

Close the clamping lever (1b).

◆

Push and pull on the armrest to ensure it is seated properly.

◆

Loosen the cap screw (2).

◆

Move the padded armrest to a comfortable position.

◆

Tighten the cap screw (2).

◆

Ensure that the armrest is seated properly.

◆

Place the patient’s arm on the armrest.

(1a)

(1b)

(2)

Summary of Contents for AXIOM Iconos R200















































































































































































































































Search results

Summary of Contents for AXIOM Iconos R200

Reviews:

Siemens AXIOM Iconos R200, Operator'S Manual, Page: 207 / 238

Search results

Summary of Contents for AXIOM Iconos R200

Reviews: