Siemens AXIOM Iconos R200 Operator'S Manual Download Page 205

Page: 205 / 238

Accessories

Optional Accessories

AXIOM Iconos R200

AXD3-340.620.13.01.02

/ 54

Foot switch assemblies for fluoroscopy and
radiography

Application

For releasing radiographic or fluoroscopic exposures during tableside examina-
tions.

Attachment

◆

Insert the foot switch plug into the receptacle in the electronics cabinet.

◆

Turn the locking ring of the plug to the right until the connector is seated prop-
erly.

◆

Route the cable along the floor appropriately.

◆

Position the patient.

Caution

Route the cable carefully to avoid safety hazards (e.g. tripping).

Do not permit the wheels of transport devices such as carts and wheelchairs to
run over the pedals of the foot switch assembly,
since this could cause inadvertent radiation release.

The following steps require radiation release.

Ensure proper radiation protection.

Summary of Contents for AXIOM Iconos R200















































































































































































































































Search results

Summary of Contents for AXIOM Iconos R200

Reviews:

Siemens AXIOM Iconos R200, Operator'S Manual, Page: 205 / 238

Search results

Summary of Contents for AXIOM Iconos R200

Reviews: