Siemens AXIOM Iconos R200 Operator'S Manual Download Page 189

Page: 189 / 238

Accessories

Optional Accessories

AXIOM Iconos R200

AXD3-340.620.13.01.02

/ 54

Compression belt

Application

Used for patient compression during thoracic or abdominal examinations as well
as for immobilizing restless or very frail patients.

Attachment

◆

Move the patient table to the horizontal position.

◆

Position the patient on the table.

◆

Push the tensioning part of the compression belt into the required position
over the front accessory rail.

Make sure that all traces of contrast medium have been removed from the com-
pression belt. Otherwise, the X-ray image will show artifacts.
The compression belt is made of transparent plastic and can be cleaned with a
damp cloth.

Summary of Contents for AXIOM Iconos R200















































































































































































































































Search results

Summary of Contents for AXIOM Iconos R200

Reviews:

Siemens AXIOM Iconos R200, Operator'S Manual, Page: 189 / 238

Search results

Summary of Contents for AXIOM Iconos R200

Reviews: