manualshive.com logo in svg

Siemens AXIOM Iconos R200, Operator'S Manual, Page: 185 / 238

Share
Download
Siemens AXIOM Iconos R200 Operator'S Manual Download Page 185

AXIOM Iconos R200

AXD3-340.620.13.01.02

13 

/ 54

Accessories

Optional Accessories

Head support

Application

Holder for cranial examinations. Can be adjusted in height, width, and lateral tilt

Attachment

◆

Move the table to the horizontal position.

◆

Loosen both cap screws (1) for attaching the head support to the accessory 
rails.

◆

Insert the head support into the accessory rails at the head end or foot end of 
the table and move it to the appropriate position.

◆

Tighten the cap screws (1).

◆

Pull the head support to ensure that it is secured properly.

◆

Turn the following cap screws as indicated to permit adjustment of the:
– (2) position from side to side.
– (3) height.
– (4) lateral tilt from 0° to ± 90° (depending on the height setting).
– (5) pads (6) to the width of the patient’s head; turn to the left.

◆

Set the position from side to side.

◆

Tighten the cap screw (2).

◆

Push and pull the head support to ensure that it is seated properly.

◆

Assist the patient in positioning his/her head in the head support.

❏

The patient’s head should make contact with the top pad.

◆

Raise the stabilizing arms to the height required.

◆

Tighten the cap screw (3).

◆

Push and pull on the stabilizing arms to ensure they are seated properly.

◆

Turn the cap screws (5) carefully to the right.

❏

Both padded stabilizing arms will move toward the patient’s head.

2

1

5

1

3

5

1

5

4

1

1

6

6

Summary of Contents for AXIOM Iconos R200















































































































































































































































Reviews:

No comments