Siemens AXIOM Iconos R200 Operator'S Manual Download Page 166

Page: 166 / 238

POLYDOROS SX 65/80

Integrated Control Console

/ 36

AXD3-340.620.13.01.02

Operator Manual

Select DR 1-point technique

❏

Setting the kV value

❏

Exposure cut-off by the automatic exposure control.

Selection

◆

Select DR technique on the unit and an organ program with DR 1-point tech-
nique

Deselection

◆

Select an organ program without DR 1-point technique

Exposure data

to be set

❏

Density compensation

❏

Measuring fields (dominants)

Display of exposure

data

❏

After the end of the exposure, the mAs and ms values in the display are flash-

ing.

Program

Iconos

Cassette

0.0

Iconos Bed

Iconos DFR

3.4
µGy*cm2

Info

%hu

0.3

min

0.1

Vertix

Summary of Contents for AXIOM Iconos R200















































































































































































































































Search results

Summary of Contents for AXIOM Iconos R200

Reviews:

Siemens AXIOM Iconos R200, Operator'S Manual, Page: 166 / 238

Search results

Summary of Contents for AXIOM Iconos R200

Reviews: