Siemens AXIOM Iconos R200 Operator'S Manual Download Page 162

Page: 162 / 238

POLYDOROS SX 65/80

Integrated Control Console

/ 36

AXD3-340.620.13.01.02

Operator Manual

Select mAs tomography

❏

Setting the kV, mAs values and the tomographic time

❏

Exposure cut-off by the mAs counter.

Selection

◆

Select a tomographic program on the unit

Deselection

◆

Deselect the tomographic program on the unit or

◆

Actuate

– a button for film-screen combination: Plani-IONTOMAT is selected

– a measuring field (dominant) button: Plani-IONTOMAT is selected or
– the IONTOMAT button: Plani-IONTOMAT with mAs preselection is

selected

Exposure data

to be set

❏

The following exposure data can be set:

– kV value
– mAs value
– Focal spot
– Tube load

100%

Program

Iconos

Cassette

0.0

Iconos Bed

Iconos DFR

80%

mAs

800

3.4
µGy*cm2

Info

%hu

0.3

min

0.1

Vertix

Summary of Contents for AXIOM Iconos R200















































































































































































































































Search results

Summary of Contents for AXIOM Iconos R200

Reviews:

Siemens AXIOM Iconos R200, Operator'S Manual, Page: 162 / 238

Search results

Summary of Contents for AXIOM Iconos R200

Reviews: