manualshive.com logo in svg

Siemens AXIOM Iconos R200, Operator'S Manual, Page: 136 / 238

Share
Download
Siemens AXIOM Iconos R200 Operator'S Manual Download Page 136

Examination

Cassette exposures with wall stand

52 

/ 52

AXD3-340.620.13.01.02

Operator Manual

Releasing the exposure

❏

To release the exposure, actuate the exposure release button on the genera-
tor ON/OFF console.

❏

Before each exposure release check:
– the collimation with the aid of the light localizer on the multileaf collimator
– the set SID with the tape measure on the multileaf collimator
– that if the dominants are changed the correct dominant is always selected
– the central ray onto the cassette center with the aid of the laser line light 

localizer on the multileaf collimator

❏

The signal lamps for radiation ON must light up.

For safety reasons, radiation cannot be released from the system control con-
sole or the footswitch in this mode.

Warning

If these radiation indicators light up although no switch has been actuated:

◆

Switch the system off immediately!

◆

Notify SIEMENS Uptime Service.

◆

Do not start the system up again.

Summary of Contents for AXIOM Iconos R200















































































































































































































































Reviews:

No comments