Siemens AXIOM Iconos R200 Operator'S Manual Download Page 126

Page: 126 / 238

Examination

Digital Radiography

/ 52

AXD3-340.620.13.01.02

Operator Manual

Examination procedure for abdominal survey images

Preparation

◆

Prepare the digital imaging system.

◆

Select the DR system at the unit remote control console.

◆

Move the patient table into the 0° position (horizontal).

◆

Position the patient, head on the left.

For reasons relating to the exposure technology, the scanning direction for DR
scanning should be from the pelvis headwards.

◆

Set vertical projection.

◆

Set the largest possible SID.

◆

Perform the examination, e.g. colon - double contrast, as usual.

◆

Press this key.
– The LED in the start key lights up if the conditions for scanning are not ful-

filled.

– DR scanning is selected.
– I.I. full format is selected.
– The rectangular height diaphragm moves automatically to the configured

value (approx.10 - 12 cm)

– The display shows 3 scanning programs with 2 directions each.
– The selected scanning program is highlighted.

By pressing the key again the next possible scanning program with direction be-
comes active.

◆

Select the scanning program for abdomen
– left arrow: scanning from right to left
– right arrow: scanning from left to right

n e

< - -

- - >

< - -

A b d ome n

- - >

Summary of Contents for AXIOM Iconos R200















































































































































































































































Search results

Summary of Contents for AXIOM Iconos R200

Reviews:

Siemens AXIOM Iconos R200, Operator'S Manual, Page: 126 / 238

Search results

Summary of Contents for AXIOM Iconos R200

Reviews: