manualshive.com logo in svg

Siemens AXIOM Iconos R200, Operator'S Manual, Page: 115 / 238

Share
Download
Siemens AXIOM Iconos R200 Operator'S Manual Download Page 115

Examination

Digital Radiography

AXIOM Iconos R200

AXD3-340.620.13.01.02

31 

/ 52

Releasing the exposure

❏

Release the exposure with the exposure release button on the system remote 
control console or via the foot switch in the control room, or table-side (op-
tion). 

❏

Radiation is released long as long as you continue to press the exposure re-
lease button.

❏

The radiation ON indicators must light up.

Radiation interruption

If you let go of the exposure release button during radiation, the exposure is in-
terrupted immediately.

Exposure end

Letting go of the exposure release button , a full image memory or reaching the 
programmed maximum scene time ends the exposure series.

Examination procedure

Preparation

◆

Prepare the digital imaging system

◆

Move the tube assembly into the 0° position

◆

Position the patient

◆

Set a nominal source-image intensifier distance of 115 cm or 150 cm

◆

Bring the X-ray system and tabletop into the intended starting position.

You must ensure that the travel range for the X-ray system is sufficient.

◆

Press this key.
– The LED lights up: Periscanning is selected.
– Serialography is selected.

Warning

If these radiation ON indicators light up although no switch has been actuated 
and the current fluoroscopic image cannot be seen on the monitor:

◆

Switch the system off immediately!

◆

Notify the SIEMENS Uptime Service.

◆

Discontinue operation of the system.

DR

DR

The LEDs in the Periscanning and start keys flash if the conditions for exposure 
are not fulfilled.

Summary of Contents for AXIOM Iconos R200















































































































































































































































Reviews:

No comments