Siemens 9810 Series User Manual Download Page 197

Page: 197 / 218

Maintenance

3. Drag the

resources

and

examples

folders into the

web

folder. Confirm to

overwrite existing files when prompted.
The files are immediately transferred to the meter.

Loading remote display firmware using ION Setup

This procedure is specific to meters with a remote display.

You can load updates to your meter’s remote display firmware using ION Setup
over an Ethernet connection.

You must have:

•

Your meter’s Remote Display firmware file (.BIN). You can download update
files from www.usa.siemens.com/pds.

•

The remote display connected to your meter.

•

FTP access to your meter from the computer running ION Setup.

NOTE:

If your meter’s remote display loses power during firmware upload, the

display will revert to its original firmware and you will have to reload the
firmware file.

1. Obtain the Remote Display firmware file (.BIN) that you want to load onto your

display. Save the files where they can be accessed by the computer running
ION Setup.

2. Start ION Setup.

3. Open the Setup Assistant for your meter.

4. Select the

Template

screen.

5. Click the

Firmware Upgrade

tab, then click

Upgrade

. Enter your meter’s

password (if prompted) and click

6. Navigate to where you have stored the remote display firmware. Select the

Remote Display firmware file (*.BIN) as the file type.

7. Select the remote display firmware (.BIN) file and click

Open

8. Enter your ION Setup password when prompted and click

A dialog box describes the firmware upgrade progress, verifies the firmware, and
finishes with an overview stating whether the firmware was successfully uploaded.

Loading remote display firmware using FTP

You can upload firmware to your meter’s remote display by loading the firmware
upgrade file onto your meter’s internal FTP site.

You must have:

•

Your meter’s remote display firmware upgrade (.BIN) file. You can download
upgrade files from www.usa.siemens.com/pds.

•

The remote display connected to your meter, and have access to your
meter’s internal FTP site.

1. Connect to your meter’s internal FTP site.

2. Open the remote display upgrade (rmdUpg) folder.

3. Drag the remote display firmware file into the remote display upgrade folder.

The file is immediately transferred to the remote display, and is not stored on
the meter.

4. Watch your meter’s display to confirm the firmware upgrade is taking place.

7EN05-0390-00

197

Summary of Contents for 9810 Series



























































































































































































































Search results

Summary of Contents for 9810 Series

Reviews:

Siemens 9810 Series, User Manual, Page: 197 / 218

Search results

Summary of Contents for 9810 Series

Reviews: