Siemens 7XV5550-0xA00 Series Manual Download Page 24 | Manualshive

Page: 24 / 52

background image

Page 24 from 52

Active Mini-Starcoupler

14.01.2002

4.3.4 RS485-Interface

X5

Connection X5 is a dual pole COMBICON screw type connector

Pin. Nr.

Meaning

Symbol

1

RS485 A

A

2

RS485 B

B

Tab. 4:

Assignment of the 9 pole Sub-D plug

4.4 LED's

The LED´s are at the front side of the device and visible. They indicate
the operation of the device.

4.4.1

Green LED "RUN"

The green LED is ON as soon as the device is ready for operation. That
means, the in5V supply voltage and the micro-processor work
correct.

4.4.2

Yellow LED "MASTER"

The yellow LED "MASTER" flashs, if datas from a switched port are
transmitted to the Master-interfaces.
If the micro-processor doesn´t operate, the LED "MASTER" is ON as
long as the LED "RUN" is in OFF-state, but +5V supply voltage is
available.

4.4.3

Yellow LED "SLAVE"

The yellow LED "SLAVE" flashs, if datas from a Master-interface are
transmitted to one of the selected Slave-interfaces.
The LED "SLAVE" is ON, as long as the micro-processor doesn´t
operate and the DIP-switch S2.1 is in "ON" position.

Note:

If datas are exchanged between the Master-interfaces of the

device and no Slave-interface is active switched no yellow LED flash.

«
...
22
23
24
25
26
...
»

Summary of Contents for 7XV5550-0xA00 Series





















































Reviews:

No comments

Related manuals for 7XV5550-0xA00 Series

Brand: ABLE Pages: 5

Brand: AbleNet Pages: 2

Brand: B&B Electronics Pages: 26

Brand: B&B Electronics Pages: 15

Brand: B&B Electronics Pages: 45

Brand: Field Controls Pages: 4

Brand: Meridian Pages: 16

PAT TRS 05 / PATB3

Brand: Hirschmann Pages: 12

Brand: Grozone Control Pages: 20

Brand: Xunison Pages: 14

iBootBar iBB-DC8

Brand: Dataprobe Pages: 36

Brand: pro bel Pages: 12

Brand: SMART-AVI Pages: 2

Brand: IPGARD Pages: 2

Brand: IOGear Pages: 10

Brand: JUKI Pages: 2

Brand: Holley Pages: 2

Brand: Black Box Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands