Siemens 7XV5550-0xA00 Series Manual Download Page 16

Page: 16 / 52

Page 16 from 52

Active Mini-Starcoupler

14.01.2002

Optical interfaces

Optical inputs / outputs

Optical connectors

Laser class 1 acc. EN60825-1/-2
Data flow indication

Wave length
Launched power

Sensitivity
Optical budget
Maximum reach
By software settable baud rates

By software settable data formats

5 transmitters, 5 receivers
Factory setting: Light OFF in idle state
FSMA (protective caps made of plastic)
alternativ on request ST connectors

LED yellow ´Master-interface transmit datas´
LED yellow ´Slave-interface transmit datas´
820 nm
50/125

m: -19dBm multimode fibre

62,5/125

m: -15dBm multimode fibre

200

m; -6,2dBm HCS fibre

-30dBm
10dB (+3 dB system budget – safety margin)
1.5 km with 62,5/125

m multimode fibre

1200, 2400, 4800, 9600, 19200, 3840, 57600,
115200 Baud
8N1, 8N2, 8E1

2.2 Safety

Tests

Safety test standards

according DIN EN 61010 Teil1
Overvoltage category
Degree of pollution
Fire resistance classification according to UL 94

III
2
V0

Dielectric tests

EN61010 IEC 255-5:
ANSI/IEEE C37.90.0

Voltage test (routine test)

Auxiliary power to relay

Auxiliary power to RS232 interface
Relay to RS232 interface

Surge voltage test (type test)

VDE0435, Teil 303

Auxiliary power to relay
Auxiliary power to RS232 interface
Relay to RS232 interface
Relay to RS485 interface

5,25 kV DC / 1s (with bypass capacitors)
3,7 kV AC / 50Hz / 1s (without bypass capacitors)
3,7 kV AC / 50Hz / 1s (without bypass capacitors)

5 kV (peak); 1,2/50

s; 0,5 J;

3 pos. and 3 neg. surges in intervals of 5 s
all circuits, class III (not on open contacts)

Summary of Contents for 7XV5550-0xA00 Series





















































Search results

Summary of Contents for 7XV5550-0xA00 Series

Reviews:

Related manuals for 7XV5550-0xA00 Series

Brands by name

Popular brands

Siemens 7XV5550-0xA00 Series, Manual

Search results

Summary of Contents for 7XV5550-0xA00 Series

Reviews:

Related manuals for 7XV5550-0xA00 Series

Brands by name

Popular brands