manualshive.com logo in svg

Siemens 7ML5430, Operating Instructions Manual, Page: 59 / 111

Share
Download
Siemens 7ML5430 Operating Instructions Manual Download Page 59

 

Parameter assignment 

 

7.21 Rate (P700 and P701) 

SITRANS Probe LR with mA/HART 
Operating Instructions, 05/2019, A5E32337711-AC 

59

 

7.21

 

Rate (P700 and P701) 

 

 

Note 
Factory settings are indicated by an asterisk (*) in the parameter tables, unless explicitly 

described. 

 

These parameters determine how material level changes are reported. 

7.21.1

 

P700 Maximum fill rate 

Allows you to further adjust the SITRANS Probe LR response to increases in the actual 

material level (or an advance to a higher Failsafe Material Level, P071). P700 is 

automatically updated whenever Measurement Response (P003) is altered. 

 

Values 

Range 

0.0000 to 99999 m/min 

Factory setting 

0.1 

Altered by 

P003 Measurement response 

Related parameters 

P005 Units 
P007 Span 
P071 Failsafe material level 

Enter a value slightly greater than the maximum vessel-filling rate, in Units (P005) or percent 

of Span (P007) per minute. 

 

P003 value 

Meters/minute 

1 

0.1 

2 

1 

3 

10 

7.21.2

 

P701 Maximum empty rate 

Adjusts the SITRANS Probe LR response to decreases in the actual material level (or an 

advance to a lower Failsafe Material Level, P071). P701 is automatically updated whenever 

Measurement Response (P003) is altered. 

 

Values 

Range 

0.0000 to 99999 m / min 

Factory setting 

0.1 

Altered by 

P003 Measurement Response 

Related parameters 

P005 Units  
P007 Span 
P071 Failsafe Material Level 

Summary of Contents for 7ML5430
















































































































Reviews:

No comments