manualshive.com logo in svg

Siemens 7ML5430, Operating Instructions Manual, Page: 14 / 111

Share
Download
Siemens 7ML5430 Operating Instructions Manual Download Page 14

Safety notes 

 

2.3 Use in hazardous areas 

 

SITRANS Probe LR with mA/HART 

14

 

Operating Instructions, 05/2019, A5E32337711-AC 

2.2.5

 

CE electromagnetic compatibility (EMC) conformity 

This equipment has been tested and found to comply with the following EMC standards: 

 

EMC standard 

Title 

CISPR 11:2009 + A1:2010/EN 

55011:2009 + A1:2010, CLASS A 

Limits and methods of measurements of radio disturbance 

characteristics of industrial, scientific, and medical (ISM) radio-

frequency equipment. 

EN 61326:2013 (IEC 61326:2012) 

Electrical Equipment for Measurement, Control and Laboratory 

Use – Electromagnetic Compatibility. 

EN61000-4-2:2009 

Electromagnetic Compatibility (EMC) Part 4-2: Testing and 

measurement techniques – Electrostatic discharge immunity 

test. 

EN61000-4-3:2006 + A1:2008 + 

A2:2010 

Electromagnetic Compatibility (EMC) Part 4-3: Testing and 

measurement techniques – Radiated, radiofrequency, electro-

magnetic field immunity test 2006 + A1:2008 + A2:2010. 

EN61000-4-4:2004 + A1:2010 

Electromagnetic Compatibility (EMC) Part 4-4: Testing and 

measurement techniques – Electrical fast transient/burst im-

munity test. 

EN61000-4-5:2006 

Electromagnetic Compatibility (EMC) Part 4-5: Testing and 

measurement techniques – Surge immunity test. 

EN61000-4-6:2010 

Electromagnetic Compatibility (EMC) Part 4-6: Testing and 

measurement techniques – Immunity to conducted disturb-

ances, induced by radio-frequency fields. 

EN61000-4-8:2010 

Electromagnetic Compatibility (EMC) Part 4-8: Testing and 

measurement techniques – Power frequency magnetic field 

immunity test. 

2.3

 

Use in hazardous areas 

Qualified personnel for hazardous area applications 
Persons who install, connect, commission, operate, and service the device in a hazardous 

area must have the following specific qualifications:  

●

 

They are authorized, trained or instructed in operating and maintaining devices and 

systems according to the safety regulations for electrical circuits, high pressures, 

aggressive, and hazardous media. 

●

 

They are authorized, trained, or instructed in carrying out work on electrical circuits for 

hazardous systems. 

●

 

They are trained or instructed in maintenance and use of appropriate safety equipment 

according to the pertinent safety regulations. 

Summary of Contents for 7ML5430
















































































































Reviews:

No comments