manualshive.com logo in svg

Siemens 7ML5430, Operating Instructions Manual, Page: 13 / 111

Share
Download
Siemens 7ML5430 Operating Instructions Manual Download Page 13

 

Safety notes 

 

2.2 Laws and directives 

SITRANS Probe LR with mA/HART 
Operating Instructions, 05/2019, A5E32337711-AC 

13

 

2.2.3

 

Radio Equipment Directive (RED) compliance (Europe) 

Hereby, Siemens declares that the SITRANS Probe LR is in compliance with the essential 

requirements and other relevant provisions of Directive 2014/53/EU. The Probe LR complies 

with EN 302 372 for use in closed storage vessels, when installed according to the 

installation requirements of EN 302 372, and may be used in all EU countries. For the 

receiver test that covers the influence of an interferer signal to the device, the performance 

criterion has at least the following level of performance according to ETSI TS 103 361 [6]: 

●

 

Performance criterion: measurement value variation Δd over time during a distance 

measurement 

●

 

Level of performance: Δd ≤ ±50 mm

 

2.2.4

 

FCC Conformity 

US Installations only: Federal Communications Commission (FCC) rules 

 

 

WARNING 

Authority to operate equipment 
Changes or modifications not expressly approved by Siemens could void the user’s 

authority to operate the equipment. 

 

 

Note 

•

 

This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 

reasonable protection against harmful interference when the equipment is operated in a 

commercial environment. 

•

 

This equipment generates, uses, and can radiate radio frequency energy and, if not 

installed and used in accordance with the instruction manual, may cause harmful 

interference to radio communications. Operation of this equipment in a residential area is 

likely to cause harmful interference to radio communications, in which case the user will 

be required to correct the interference at his own expense. 

 

 

 

Summary of Contents for 7ML5430
















































































































Reviews:

No comments