manualshive.com logo in svg

Siemens 7ME6810, Operating Instructions Manual, Page: 96 / 170

Share
Download
Siemens 7ME6810 Operating Instructions Manual Download Page 96

Transmitter

MAG 8000Standard

(7ME6810)

MAG 8000 CT

(7ME6820)

Flow unit

Europe std.

Volume: m

3

 

Flow rate: m

3

/h

US std.

Volume: Gallon

Flow rate: GPM

Volume: m

3

 

Flow rate: m

3

/h

Australia std.

Volume: ML

Flow rate: ML/d

Volume: m

3

 

Flow rate: m

3

/h

Other selectable 

units

Volume:

m

3

 x 100, L x 100, G x 100, G x 1000, 

MG,

CF x 100, CF x 1000, AF, Al, kL, 

BBL42

Flow rate:

m

3

/min, m

3

/h, m

3

/d, L/s, L/min, L/h, ML/

d, GPS, GPH, GPD, MGD, GPM, 

CFS, CFM, CFH, BBL42/s, BBL42/

min, BBL42/h, BBL42/d

-

Other units than m

3

 and m

3

/h (ordered 

from factory or manually configured 

on-site by changing scaling factors) 

are shown by a label stuck onto display

Digital output

Nos.

2 passive outputs (MOS), individually galvanically isolated

Load

Max. ± 35 V DC, 50 mA short circuit protected

Output A

Programmable as:

Pulse volume, Forward, Reverse, Forward/net, Reverse/net

Output B

Programmable as:

Pulse volume, Forward, Reverse, Forward/net, Reverse/net , Alarm, Call-up

Pulse rate

Pulse A: Max. 100 Hz

Pulse B: Max. 50 Hz

Pulse width

5, 10, 25, 50, 100, 500 ms

Communication

IrDA

Standard integrated infrared communication interface with MODBUS RTU pro‐

tocol

Add-on modules

RS 232 serial interface with MODBUS RTU (Rx/Tx/GND),

point to point with max. 15 m cable

RS 485 serial interface with MODBUS RTU (+/-/GND),

multidrop with up to 32 devices with max. 1000 m cable

Encoder interface module (for Itron 200WP) "Sensus protocol"

Wireless communication module with or without analog input cable

10.4

Power supply

Power supply
Battery power supply 

1)

Internal battery pack

1 D-Cell 3.6 V / 16 Ah

Internal battery pack

2 D-Cell 3.6 V / 33 Ah

External battery pack

4 D-Cell 3.6 V / 66 Ah

Technical data
10.4 Power supply

SITRANS FM MAG 8000

96

Operating Instructions, 03/2020, A5E03071515-AH

Summary of Contents for 7ME6810











































































































































































Reviews:

No comments