manualshive.com logo in svg

Siemens 7ME305, Operating Instructions Manual, Page: 11 / 124

Share
Download
Siemens 7ME305 Operating Instructions Manual Download Page 11

Safety notes

2

2.1

General safety instructions

CAUTION

Correct, reliable operation of the product requires proper transport, storage, positioning 
and assembly as well as careful operation and maintenance.

Only qualified personnel should install or operate this instrument.  

Note

Alterations to the product, including opening or improper modifications of the product are not 
permitted.

If this requirement is not observed, the CE mark and the manufacturer's warranty will expire.

2.2

Laws and directives

General requirements     

Installation of the equipment must comply with national regulations. For example EN 60079-14 
for the European Community.

Instrument safety standards   

The device has been tested at the factory, based on the safety requirements. In order to maintain 
this condition over the expected life of the device the requirements described in these Operating 
Instructions must be observed.

NOTICE
Material compatibility  

Siemens Flow Instruments can provide assistance with the selection of wetted sensor parts. 
However, the full responsibility for the selection rests with the customer and Siemens Flow 
Instruments can take no responsibility for any failure due to material incompatibility.

SITRANS FUS060 with PROFIBUS PA
Operating Instructions, 09/2021, A5E02225054-AD

11

Summary of Contents for 7ME305





























































































































Reviews:

No comments