manualshive.com logo in svg

Siemens 7MB2041, Operating Instructions Manual, Page: 60 / 152

Share
Download
Siemens 7MB2041 Operating Instructions Manual Download Page 60

Operation 

 

5.4 Operating functions 

 

OXYMAT 64 

58

 

Operating Instructions, 06/2008, A5E00880383-03 

5.4.3.6

 

Autocal (function 24) 

 

 

Note 
You can only make use of automatic calibration (Autocal) if your device contains additional 

electronics (optional board). If this isn't the case, a corresponding message will appear on 

the display when the Autocal function is called. 
Automatic calibration can only be started if the device is in the "Measure" operating state! 

 

Autocal/-check            O

2

 

Figure 5-14  Autocal function 

 

 

Note 
The settings for "Autocal/Check..." (subfunctions 1 to 3) are valid both for Autocal (automatic 

calibration) and for Autocal Check (automatic check that the set calibration tolerances are 

complied with, without calibration). 
The settings for "Autocal Check" (4th subfunction) only refer to the check of the calibration 

tolerances without calibration. 

 

AUTOCAL/Check operating mode 

Autocal/-check mode       O

2

 

Figure 5-15  AUTOCAL/Check operating mode 

Summary of Contents for 7MB2041

























































































































































Reviews:

No comments