Siemens 6GT2002-0HD01 Operating Instructions Manual Download Page 51

Page: 51 / 72

SIMATIC RF170C
Operating Instructions, 02/2022, J31069-D0176-U001-A6-7618

Technical data

Table 8- 1

Technical specifications for RF170C

6GT2002-0HD01

Product type designation

SIMATIC RF170C

Technical specifications -

interfaces

Serial interface to the user

PROFIBUS DP-V1, PROFINET IO

Interface to the ET 200pro

ET 200pro backplane bus

Connector system

See “ET 200pro” operating instructions

Transmission speed

See “ET 200pro” operating instructions

Max. block length

2 words cyclic/240 bytes acyclic

(per channel)

Serial interface to the reader

Connector

2 x M12 connector plug

Max. cable length

•

RS-422

1000 m, dependent on reader

(preassembled cables 2..50 m for other standard cables and

self-assembled cables, refer to the section "Connecting cables")

•

RS-232

30 m

Connectable readers

2 x reader

Software functions

Programming

Depending on the PROFIBUS DP master

SIMATIC S7 function blocks

Ident profile/Ident blocks/RFID standard profile

FB 45 / FB 55

Transponder addressing

Direct access via addresses

Electrical data

Supply voltage

•

Rated value

24 VDC

•

Permitted range

20 to 30 VDC

Current consumption

Max. 1 A; typ. 130 mA (without reader)

Current taken from reader outputs
•

RS-422

max 800 mA at 24 VDC

(in total for one or two readers.)

•

RS-232

max 1200 mA at 5 VDC

(in total for one or two readers.)

Electrical isolation

yes

Summary of Contents for 6GT2002-0HD01









































































Search results

Summary of Contents for 6GT2002-0HD01

Reviews:

Siemens 6GT2002-0HD01, Operating Instructions Manual, Page: 51 / 72

Search results

Summary of Contents for 6GT2002-0HD01

Reviews: