manualshive.com logo in svg

Siemens 6GT2002-0HD01, Operating Instructions Manual, Page: 32 / 72

Share
Download
Siemens 6GT2002-0HD01 Operating Instructions Manual Download Page 32

Parameter settings 

 

5.2 Configuration via STEP 7 (Basic/Professional) 

 

SIMATIC RF170C 

32

 

Operating Instructions, 02/2022, J31069-D0176-U001-A6-7618 

Parameter 

Parameter value 

Default value 

Description 

Suppression of  

Error LED 

None 

Channel 1 

Channel 2 

None 

Disabling the Error LED (ERR) of a channel.  

The communications module has two channels 

to which the readers / optical readers can be 

connected. The Error LED of the other channel 

flashes permanently when only one of the 

channels is being used. With the help of the 

suppression, you can disable the Error LED of 

the unused channel. 

Interface 

RS-232 

RS-422 

-- 

2)

 

Selection of the interface type that the 

connected hardware (reader / optical reader) 

uses. 

This parameter only needs to be set if the MOBY 

mode “Freeport protocol” was selected. 

 

1)

  The MOBY mode “RF300 filehandler” is not supported by the RF170C communications module. 

2)

  The default value depends on the set MOBY mode. 

5.2.3

 

"Frame" parameter group 

The "Frame" parameter group is only displayed when you have selected the parameter value 

"Freeport protocol" in the "MOBY Mode" parameter of the module parameters. In this 

parameter group, you can configure all parameters specific to the "Freeport protocol".  
The “Frame“ parameter group contains the following parameters: 

 

Figure 5-3 

Parameters in the "Frame" parameter group 

Summary of Contents for 6GT2002-0HD01









































































Reviews:

No comments