Siemens 6GK7 542-1AX00-0XE0 Operating Instructions Manual Download Page 23 | Manualshive

Page: 23 / 54

background image

Installation, connecting up, commissioning, operation

3.1 Important notes on using the device

CM 1542-1
Operating Instructions, 07/2019, C79000-G8976-C355-04

23

3.1.3

Notices regarding use in hazardous areas according to UL HazLoc

This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or non-

hazardous locations only.
This equipment is suitable for use in Class I, Zone 2, Group IIC or non-hazardous locations

only.

WARNING

EXPLOSION HAZARD
You may only connect or disconnect cables carrying electricity when the power supply is

switched off or when the device is in an area without inflammable gas concentrations.

3.1.4

Notices on use in hazardous areas according to FM

WARNING

EXPLOSION HAZARD
You may only connect or disconnect cables carrying electricity when the power supply is

switched off or when the device is in an area without inflammable gas concentrations.

This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or non-

hazardous locations only.
This equipment is suitable for use in Class I, Zone 2, Group IIC or non-hazardous locations

only.

WARNING

EXPLOSION HAZARD
The equipment is intended to be installed within an ultimate enclosure. The inner service

temperature of the enclosure corresponds to the ambient temperature of the module. Use

installation wiring connections with admitted maximum operating temperature of at least

30 ºC higher than maximum ambient temperature.

«
...
21
22
23
24
25
...
»

Summary of Contents for 6GK7 542-1AX00-0XE0























































Reviews:

No comments

Related manuals for 6GK7 542-1AX00-0XE0

Brand: Panasonic Pages: 3

Brand: GSK Pages: 32

Brand: Easun Pages: 6

Brand: Goodmans Pages: 22

SoundPoint Pro SE-220

Brand: Polycom Pages: 2

Brand: Grundig Pages: 16

Brand: Rath Pages: 7

Brand: ICON Pages: 6

Brand: Walkera Pages: 22

ClearSound LoopHEAR 101

Brand: Geemarc Pages: 19

Brand: Mi-Light Pages: 5

Brand: GE Pages: 96

Brand: JVC Pages: 19

Brand: JVC Pages: 36

Brand: JVC Pages: 2

Voiceducer MDRMN4044

Brand: Motorola Pages: 18

Brand: Motorola Pages: 18

Brand: Motorola Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands