manualshive.com logo in svg

Siemens 6GK5748-1GY01-0AA0, Operating Instructions Manual, Page: 33 / 91

Share
Download
Siemens 6GK5748-1GY01-0AA0 Operating Instructions Manual Download Page 33

 

Description of the device 

 

4.5 LED display 

SCALANCE W1788-x / W1748-1 
Operating Instructions, 03/2022, C79000-G8976-C484-05 

33

 

 

 

Note 
Primary user (radar) on all enabled channels 

If the device detects competing radar signals on all enabled channels of the WLAN 

interface, the 

F

 LED is lit and 

R1

 flash. No data traffic is then possible for the next 30 

minutes. After this time, the device runs the scan again and checks whether a primary 

user still exists. If no primary user is detected, data traffic is possible again. 
The wait time of 30 minutes is necessary due to legal requirements and cannot be 

shortened even by restarting the device. 

 

4.5.2

 

SCALANCE W1788-2 / W1788-2IA 

Information on operating status and data transfer 

On the front of the housing, several LEDs provide information on the operating status of 

the device: 

 

Summary of Contents for 6GK5748-1GY01-0AA0




























































































Reviews:

No comments