manualshive.com logo in svg

Siemens 6GK5748-1GY01-0AA0, Operating Instructions Manual, Page: 28 / 91

Share
Download
Siemens 6GK5748-1GY01-0AA0 Operating Instructions Manual Download Page 28

Description of the device 

 

4.4 Accessories 

 

SCALANCE W1788-x / W1748-1 

28

 

Operating Instructions, 03/2022, C79000-G8976-C484-05 

4.4.5.2

 

Lightning protection 

 

Component 

Description 

Article number 

LP798-1N  

Lighting protector with N/N 

female/female connector with gas 

discharge technology 

6GK5798-2LP00-2AA6 

LP798-2N 

Lighting protector with N/N 

female/female connector with quarter 

wave technology 

6GK5798-2LP10-2AA6 

4.4.5.3

 

Terminating resistor 

 

Component 

Description 

Article number 

TI795-1N 

Electrical connector N-Connect, male 
Pack of 1 

6GK5795-1TN00-1AA0 

4.4.5.4

 

Cabinet feedthrough 

 

Component 

Description 

Article number 

IE M12 Panel Feedthrough 

4 x 2 

Cabinet feedthrough for conversion 

from M12 connector technology (X-

coded, IP65/67) to RJ-45 connector 

technology (X-coded, IP20) 
pack of 5 

6GK1901-0DM40-2AA5 

N-Connect/N-Connect 

Female/Female Panel 

Feedthrough 

Cabinet feedthrough for wall 

thicknesses up to 4.5 mm, two N-

Connect female connectors 

6GK5798-2PP00-2AA6 

N-Connect/SMA 

Female/Female Panel 

Feedthrough 

Panel feedthrough for wall thicknesses 

up to a maximum of 5.5 mm, two N-

Connect/SMA female connectors. 

6GK5798-0PT00-2AA0 

4.4.5.5

 

Antennas 

 

 

Note 

When you select an antenna, keep in mind the national approvals for your device. 
You will find more detailed information in Wireless approvals 

(

https://www.siemens.com/wireless-approvals

). 

 

The SCALANCE W1788-2IA uses internal omni antennas (7 dBi at 2.4 GHz and 5 dBi at 5 

GHz). 

Summary of Contents for 6GK5748-1GY01-0AA0




























































































Reviews:

No comments