manualshive.com logo in svg

Siemens 6GK5 124-0BA00-3AR3, Operating Instructions Manual

Share
Download
Siemens 6GK5 124-0BA00-3AR3 Operating Instructions Manual Download Page 45

Technical specifications
Installation options

• 19" rack mounting
• DIN rail
• Wall mounting

Mean time between failure (MTBF)
MTBF (EN/IEC 61709; 40 °C) > 90 years

6.3

Technical specifications of the SCALANCE XR124WG (240 VAC 

variant)

The following technical specifications apply to the SCALANCE XR124WG.

Technical specifications
Connection to Industrial Ethernet
Electrical connectors

Quantity

24

Connector

RJ45 jack

Properties

Half/full duplex, MDI‑X pinning

Transmission speed

10 / 100 Mbps

Electrical data
Power supply

Design

Socket, 3 pin

Rated voltage

100 to 240 V AC

Voltage range

85 to 264 VAC

Frequency

50 Hz to 60 Hz

Frequency range

47 Hz to 63 Hz

Properties

Not implemented redundantly

Current consumption

At 100 VAC

150 mA

At 240 V AC

75 mA

Effective power loss

 

7.5 W

Permitted ambient conditions
Ambient temperature 

1)

During operation up to 3000 m above mean 
sea level

0 ℃ to +60 ℃

During storage

-40 °C to +85 °C

During transportation

-40 °C to +85 °C

Relative humidity

During operation at 25 ℃

≤ 95% without condensation

Housing, dimensions and weight
Design

Rack

Housing material

Metal

Degree of protection

IP30

Dimensions (W x H x D)

482.6 x 43.6 x 177 mm

Weight

3300 g

Technical specifications

6.3 Technical specifications of the SCALANCE XR124WG (240 VAC variant)

SCALANCE XR-100WG
Operating Instructions, 09/2020, C79000-G8976-C455-04

45

Summary of Contents for 6GK5 124-0BA00-3AR3































































Reviews:

No comments

Brands by name

Popular brands

Load more brands