Siemens 6GK5 124-0BA00-3AR3 Operating Instructions Manual Download Page 44

Page: 44 / 62

Technical specifications
Installation options

• 19" rack mounting
• DIN rail
• Wall mounting

Mean time between failure (MTBF)
MTBF (EN/IEC 61709; 40 °C)

> 47 years

6.2

Technical specifications of the SCALANCE XR124WG (24 VDC

variant)

The following technical specifications apply to the SCALANCE XR124WG.

Technical specifications
Connection to Industrial Ethernet
Electrical connectors

Quantity

Connector

RJ45 jack

Properties

Half/full duplex, MDI‑X pinning

Transmission speed

10 / 100 Mbps

Electrical data
Power supply

Design

Terminal block, 2 terminals

Rated voltage

24 VDC

Voltage range

19.2 to 28.8 VDC Safe Extra Low Voltage (SELV)

Cable cross section

≥ 0.75 mm

(20 AWG)

Property

Implemented redundantly

Fusing

5 A / at least 60 V
Or power supply with LPS or NEC class 2

Current consumption

250 mA

Effective power loss

6 W

Permitted ambient conditions
Ambient temperature

During operation up to 3000 m above mean
sea level

0 ℃ to +60 ℃

During storage

-40 °C to +85 °C

During transportation

-40 °C to +85 °C

Relative humidity

During operation at 25 ℃

≤ 95% without condensation

Housing, dimensions and weight
Design

Rack

Housing material

Metal

Degree of protection

IP30

Dimensions (W x H x D)

482.6 x 43.6 x 127 mm

Weight

2700 g

Technical specifications
6.2 Technical specifications of the SCALANCE XR124WG (24 VDC variant)

SCALANCE XR-100WG

Operating Instructions, 09/2020, C79000-G8976-C455-04

Summary of Contents for 6GK5 124-0BA00-3AR3































































Search results

Summary of Contents for 6GK5 124-0BA00-3AR3

Reviews:

Brands by name

Popular brands

Siemens 6GK5 124-0BA00-3AR3, Operating Instructions Manual

Search results

Summary of Contents for 6GK5 124-0BA00-3AR3

Reviews:

Brands by name

Popular brands