manualshive.com logo in svg

Siemens 6GK1411-1AC00, Operating Instructions Manual, Page: 56 / 150

Share
Download
Siemens 6GK1411-1AC00 Operating Instructions Manual Download Page 56

Configuration 

 

4.6 Interface configuration 

 

SIMATIC CC7 

56

 

Operating Instructions, 10/2019, C79000-G8976-C503-02 

●

 

Software version 
Current firmware version of the device 

●

 

CLP 
Shows whether a CLP is currently inserted. 

Process interface (P2) 

The parameter group displays the current address data of the P2 interface. 

●

 

MAC address 

●

 

IPv4 
Address parameters, Default router 

Cloud interface (P1) 

The parameter group displays the current address data of the P1 interface. 

●

 

MAC address 

●

 

IPv4 / IPv6 
Address parameters, Default router 

DNS server 

The parameter group shows the IPv4 addresses of up to two configured DNS servers. 

4.6

 

Interface configuration 

4.6.1

 

Ethernet 

In this tab, you configure the address data of the Ethernet interfaces of the device. 

Interface and factory default addresses 

You configure the following interfaces on the web page: 

●

 

Process interface (P2) 
The interface (P2) is used for connecting to the subnet of the process stations. 

●

 

Cloud interface (P1) 
The interface (P1) is used for connecting to the Internet or to a router over which the 

broker or the network with OPC UA clients can be reached. 

The device supports IPv4 addresses, and for cloud access also IPv6 addresses. 
The following address data is preset in the factory: 

Summary of Contents for 6GK1411-1AC00























































































































































Reviews:

No comments