Siemens 6GK1411-1AC00 Operating Instructions Manual Download Page 3

Page: 3 / 150

SIMATIC CC7
Operating Instructions, 10/2019, C79000-G8976-C503-02

Preface

CAUTION

To prevent injury, read the manual before use.

Products

This document contains information on the following products:
SIMATIC CC712 / SIMATIC CC716

Hardware product version 1

Firmware version V1.2

Gateway for connection of a SIMATIC S7 or Modbus station to a cloud system, OPC UA

server for SIMATIC S7 data

Figure 1

SIMATIC CC716

The MAC address of the device is located below the socket for the power supply. You will

find the article number on the device front.
You will find the hardware product version on the right side of the device as placeholder "X".

"X 2 3 4", for example, indicates hardware product version 1.

Validity

This manual is valid for the following products:

Product name

Article number

Functions

SIMATIC CloudConnect 712 6GK1411-1AC00

Connection of 1 process station over Ethernet

SIMATIC CloudConnect 716 6GK1411-5AC00

Connection of up to 7 process stations
In addition: 1 digital input, 1 digital output,

PROFIBUS DP connection

Individual paragraphs or sections that are only valid for the CC716 are labelled with the short

form of the device.

Example: "PROFIBUS (CC716)"

Summary of Contents for 6GK1411-1AC00























































































































































Search results

Summary of Contents for 6GK1411-1AC00

Reviews:

Siemens 6GK1411-1AC00, Operating Instructions Manual, Page: 3 / 150

Search results

Summary of Contents for 6GK1411-1AC00

Reviews: